Showing posts with label stereo. Show all posts
Showing posts with label stereo. Show all posts

Wednesday, October 1, 2014

Simplest 12 Watt Stereo Amplifier Circuit

  The Type TDAl52l from Valvo/Mullard is an integrated HiFi stereo power amplifier designed for mains fed applications such as stereo TV The device works optimally when fed from a j 16V supply; and delivers a maximum output power of 2x12 W into 8 Q.
The gain of the amplifiers is fixed internally at 30 dB with a spread of 0.2 dB to ensure optimum gain balance between the channels. A special feature of the chip is its built-in mute circuit, which disconnects the non-inverting inputs when the supply voltage g is less than j 6Vj a level at which the amplifiers are still correctly biased. This arrangement ensures the absence of unwanted clicks and other noise when the amplifier is switched on or off. The TDAl52l is protected against output short circuits and thermal overloading. The SIL9 package should be bolted onto a heat- sink with a thermal resistance of no more than 3.3 K/W (R1.=8 Q; Vs: ;r 16 V; Pa=l4.6 W; Ta: 65 °C). Note that the metal tab on the chip package is internally connected to pin 5. The accompanying photograph shows that this high quality stereo amplifier has a very low component count, and is readily constructed on a piece of Veroboard. The following technical data are stated as typical in the data- sheets for the TDAl52l   

Distortion at Pa: 12 W:
0.5%
Quiescent current:
40 mA
Gain balance:
0.2 dB
Supply ripple rejection:
60 dB
Channel separation:
70 dB
Output offset voltage:
20 mV
3 dB power bandwidth:
20-20,000 Hz
Read More..

Wednesday, September 10, 2014

Stereo Power Amplifier 3000W

Amplifier Description:

This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this. Supply voltage needed by the power of this amplifier is the optimal working order symmetrical 130VDC (130VDC-130VDC ground). 1500W amplifier circuit below is a picture series of mono, stereo if you want to make it necessary to make two copies of the circuit. For more details can be viewed directly image the following 1500W power amplifier circuit. In the above series of power amplifier 1500W is equipped to control a DC Offset function to set the power amplifier is turned on at the moment and with no input signal then the output should be 0VDC. Then also equipped with a flow regulator to the power amplifier bias. Final part of this power amplifier requires adequate cooling to absorb the heat generated. Power amplifier is not equipped with a speaker protector, therefore it is necessary diapsang protector on the speaker output so that when the power amplifier is not the case turned on the beat to the speaker that can damage the speaker.The 1N5404 diodes can withstand a peak non-repetitive current of 200A.Higher rated components may be used if desired. The voltage rating needs to be at least 400V.

Amplifier circuit diagram:













Read More..

Saturday, August 30, 2014

Transistored Stereo Tone Control

Here the schema diagram of stereo tone control system which also available on the market in schema kit, you might get the kit at electronic component/part store near your area. The tone control require 12v of supply voltage to work.



The schema designed based on common tone control schema, by using two transistors FCS9014 in each channel, so there are actually four transistors in this 12v stereo tone control. Take a note that you need to install the schema prior to the amplifier device. The output of tone control should be connected towards the input of the audio amplifier. Any small signal NPN transistor such as BC547B, 2N3904, C828, or C945 may be put to use to replace FCS9014.
Read More..

Thursday, August 21, 2014

2 x 6 W stereo power amplifier

Description
The TDA1517 is an integrated class-B dual output  amplifier in a plastic single in-line medium power package  with fin (SIL9MPF), a plastic rectangular-bent single in-line  medium power package with fin (RBS9MPF) or a plastic  heat-dissipating dual in-line package (HDIP18). The  device is primarily developed for multi-media applications.

Circuit Diagram
2 x 6 W stereo power amplifier

Read More..